I have one of the new disconnects I
got from Bill this winter.
My battery cables are kind of funky,
they are autopart store clamps where the wire is clamped by a flat plate.
The PO had a good idea using the screw top posts, the clamp is put on the
post and tightened and then a nut and washer are put on the top screw portion
of the battery post and tightened down forcing the clamp onto the taper
of the post. I really should get made up battery cables but that would
be one more expense on top of my planned purchase of the Alltrax controller.
I'm looking forward to removing all the wiring out of my tractor, all the
mods by the PO and having it be relatively simple.
The spirit is willing but the wallet
is weak :-)
Jeff Tickner
Technical Support
800-545-9485, Ext 536
SoftLanding Systems
Christopher Zach <czach computer org> Sent by: elec-trak-bounces cosmos phy tufts edu
07/12/2004 09:21 AM
To
Jeff Tickner <JeffT softlanding com>
cc
elec-trak cosmos phy tufts edu
Subject
Re: (ET) charging
Sounds like your batteries are pretty good, however
your problem might
be in either the battery clamps, the wires, or your main disconnect.
I've noticed that there is a *serious* voltage drop on my tractor's
wires, life is like that.
For my part, my meter drops under load, but my battery monitors don't
show a problem. Monitors don't lie.
One way to find loose clamps is to drive the tractor around at full
power for awhile, then stop, pop the hood or seat and touch each post
with your hand. You'll feel warm (=loose) ones quickly.
Chris
Jeff Tickner wrote:
>
> In preparation for pulling my E15 apart for R&R I decided to put
a
> really good equalization charge on my pack so I ran the charger
> overnight. I reached a max voltage of 43.4 and all battery cells were
> bubbling. After I unhooked the charger and let the pack sit a half
hour
> the voltage dropped to 39.5, all the batteries were within .1 volt
of
> one another.
>
> Still I think I have a bad cell since after I buttoned it up and drove
> it to the shed the "gas gauge" dropped a good bit from driving
150
> yards. I didn't have time to check battery voltage at that time, but
is
> that the best way to find a bad cell, run the batteries down some
and
> see which battery has discharged the most?
>
> PS I have one of those "Solargizers" that I purchased because
the shed
> were the tractor is normally parked doesn't have power. While I was
> cleaning connections yesterday I tested output unconnected to the
pack
> and it was 60+V in full sun. The meter I was using (actually a dwell
> meter) doesn't have milliamps so I couldn't check output but it's
very
> small.
>
> Jeff Tickner
> Technical Support
> 800-545-9485, Ext 536
> SoftLanding Systems
>
>
> *neil <wombat dssinternet net>*
> Sent by: elec-trak-bounces cosmos phy tufts edu
>
> 07/09/2004 05:11 PM
>
>
> To
> elec-trak cosmos phy tufts edu
> cc
>
> Subject
> (ET)
charging
>
>
>
>
>
>
>
>
> You're right, that is way too low, I did a fatfinger, Should
have been
> 14.7 or more. I usually use a value of 2.7 volts per cell as
the max.
> The auto charging systems I worked with were set to 14.4 volts nominal
> at under hood temps.
>
>
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
>
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
_______________________________________________
Elec-trak mailing list
Elec-trak cosmos phy tufts edu
https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak