You will need the service manual from Bill Gunn or ask on the mail
group. My E12 has no circuit cards. If I get a chance I will look in the
service manual and try to figure something out for you. I need to fix My
E12 as I blew a diode (again) that's in the reversing circuit. The
tractor only runs in reverse right now. The E12 is my back up tractor
and I have not needed it this summer. I use the batteries in it as a
backup for the UPS system for the house. I have a cord and connector
system to connect between the tractor and the UPS battery bank. They all
use the same golf cart batteries so it's a good match.
With out the service drawing it's hard to figure anything out about the
wiring on the tractors. Even with the drawings it's still hard!
Dwight
Dwight L. Hazen, Indiana University, UITS
Bloomington, In. 47408-7378
812-855-5367 IP phone 812-856-9229
hazen indiana edu http://php.ucs.indiana.edu/~hazen/
Ham Radio wb9tlh arrl net http://wb9tlh.ampr.us
"The complexity of your life is directly proportional to how many gas
engines you own - 2 cycles count double."
-----Original Message-----
From: Richard Zachary [mailto:njcfsa earthlink net]
Sent: Monday, November 10, 2003 2:55 PM
To: Hazen, Dwight L
Subject: Re: (ET) Tractor ride not smooth
Hi Dwight,
Thanks for the response. I am a novice at this having just gotten the
E12 in June and have little background experience.
Anyway, went out and tested it and yes, the load meter bobs up and down
corresponding to the movement of the tractor.
Was able to look under and see that the drive motor pulley was clear of
the wiring, so that, at least, eliminates that.
As to field voltage, I went to the "Home Owner's Service Manual" that
came with the tractor and tried to find info on field weakening. Found
some info for the E12S that shows a card #1 and a FW connection. But
when I opened my E12, I couldn't find the card #1. Doesn't look like the
E12 has such a card or its located some place else.
Can you give me any specifics on where to look for a loose connection?
I think the reverse relay should be on the back of the dash panel on the
left side (away from the speed control). What do I do with this reverse
relay when I find it?
Don't be afraid to insult my intelligence by being overly specific.
ASSUME THAT I KNOW NOTHING.
Thanks very much,
Richard "Zack" Zachary
Hazen, Dwight L wrote:
Zack,
What is the reading on the load meter? Is it going up and down with
the
jerks? It may be a wiring problem or a contactor/relay problem. I
wonder
if your field voltage is steady. The reversing relay may be the place
to
start. Also is the motor drive pulley wearing through the wiring
harness under the frame?
Dwight
Dwight L. Hazen, Indiana University, UITS
Bloomington, In. 47408-7378
812-855-5367 IP phone 812-856-9229
hazen indiana edu http://php.ucs.indiana.edu/~hazen/
Ham Radio wb9tlh arrl net http://wb9tlh.ampr.us
"The complexity of your life is directly proportional to how many gas
engines you own - 2 cycles count double."
-----Original Message-----
From: elec-trak-bounces cosmos phy tufts edu
[mailto:elec-trak-bounces cosmos phy tufts edu] On Behalf Of Richard
Zachary
Sent: Monday, November 10, 2003 11:17 AM
To: Elec-trak list
Subject: (ET) Tractor ride not smooth
My tractor bucks some. That is, the ride is herky-jerky. It seems
worse in reverse than forward.
Is there some adjustment I can make?
Did I tighten the drive belt too much maybe?
Thanks for any advice you may be able to give.
Zack
E12
_______________________________________________
Elec-trak mailing list
Elec-trak cosmos phy tufts edu
https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak