[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ET) Power Disconnect for an E12M
- Subject: Re: (ET) Power Disconnect for an E12M
- From: "MR23=Christopher Meier \(Mtka, MN, USA\)" <mr23 worldspy net>
- Date: Sat, 29 Apr 2000 12:21:13 -0500
- Organization: Mr23
- References: <200004281353.JAA19944@mailfw6.ford.com> <001401bfb1e5$4ad89bc0$039d1e26@snaugler>
- Sender: owner-elec-trak cosmos5 phy tufts edu
I ordered a new power disconnect up from Bill this morning.
He's charging $32.50 for a part # OP134 power disconnect.
Steve, is this the same unit you refer to? How long ago did
you order it at < $20? Thanks.
Christopher M. Meier
----- Original Message -----
From: "Steve & Sandy Naugler" <snaugler earthlink net>
To: "Elie, Larry (L.D.)" <lelie ford com>; "Chris Meier"
<ChrisM pptvision com>; <ThompsonG DFO-MPO GC CA>;
<elec-trak cosmos5 phy tufts edu>
Sent: Saturday, April 29, 2000 9:14 AM
Subject: Re: (ET) Power Disconnect for an E12M
> Larry and others
> My E15's switch did fail. I then removed two different switches from
> non running tractors, and they were both bad. I started swapping parts
> to
> build one good one, and none of the parts were good enough. Bill gunn's
new
> style was the right choice. I'll replace any old style leftovers with
> the
> new style from now on.
>
> Steve Naugler
>
> ----- Original Message -----
> From: "Elie, Larry (L.D.)" <lelie ford com>
> To: "'Steve & Sandy Naugler'" <snaugler earthlink net>; "Chris Meier"
> <ChrisM pptvision com>; <ThompsonG DFO-MPO GC CA>;
> <elec-trak cosmos5 phy tufts edu>
> Sent: Friday, April 28, 2000 9:52 AM
> Subject: RE: (ET) Power Disconnect for an E12M
>
>
> > Bill also claims his has lower resistance across the device. The
> difference
> > is
> > probably trivial for power consumption, but will keep the device
> temperature
> >
> > lower. BTW, I have yet to fail an ORIGINAL switch.
> >
> > Larry Elie
> >
> >
> > -----Original Message-----
> > From: Steve & Sandy Naugler [mailto:snaugler earthlink net]
> > Sent: Thursday, April 27, 2000 11:23 PM
> > To: Chris Meier; ThompsonG DFO-MPO GC CA;
> > elec-trak cosmos5 phy tufts edu
> > Subject: Re: (ET) Power Disconnect for an E12M
> >
> >
> > When I bought Bill Gunn's replacement disconnect it cost less than $20
and
> > included a heavy circuit board to accomodate the fusible link. I don't
> > think you can go wrong with the unit Bill sells.
> >
> > Steve Naugler
> >
> > ----- Original Message -----
> > From: "Chris Meier" <ChrisM pptvision com>
> > To: <ThompsonG DFO-MPO GC CA>; <elec-trak cosmos5 phy tufts edu>
> > Sent: Thursday, April 27, 2000 10:59 AM
> > Subject: RE: (ET) Power Disconnect for an E12M
> >
> >
> > >
> > > I was at a Northern Tool store last night, and they had a Pollak
> > > brand
> > > battery disconnect switch, rated 6-36v, 150amps, for $20. The
> > > ratings
> > > are a bit low for worst-case conditions. I don't know the price or
> > ratings
> > > of the newer disconnect unit that Bill Gunn sells, but you'd probably
be
> > > better off using the unit he sells (based on past recommendations).
> > >
> > > On Thursday, April 27, 2000 6:51 AM, ThompsonG DFO-MPO GC CA
> > > [SMTP:ThompsonG DFO-MPO GC CA] wrote:
> > > > So, Here is the question/problem?
> > > > I need or would like to find a Power Disconnect for an E12. At the
> > moment
> > > I
> > > > just have a hole on the side of the tractor where it should go and
> > > > a
> > green
> > > > wire dangling from the Amp Meter. If you have one you are willing
> > > > to
> > sell
> > > > me. Please E-mail me
> > > >
> > > > I was digging around in my new E12 and discovered a lose green wire
> > under
> > > > the dash. It came from the Amp meter. After a little while of
staring
> at
> > > the
> > > > schematics and the wiring diagrams in the manual. It finally
> > > > clicked
I
> > > have
> > > > no power disconnect. Therefore I have no place to connect the Amp
> meter.
> > > My
> > > > goal is to restore this ET to nearly, new condition so I need a
power
> > > > disconnect.
> > > >
> > > > Geof Thompson B. Sc.
> > > > Data Management Engineer
> > > > Canadian Hydrographic Service
> > > > Central and Arctic Region
> > > > 867 Lakeshore Road
> > > > Burlington, Ontario
> > > > Canada. L7R 4A6
> > > >
> > > >
> > > > Phone (905) 336-4698
> > > > Fax (905) 336-4698
> > > > E-mail Thompsong dfo-mpo gc ca
> > >
> > >
> >
>
>