Re: (ET) Looking for some deck motors,,ET15

[Chris Zach <cz alembic crystel com>]

I would like to point out to the list that when you order a "deck motor" 
from Harold you don't get a "motor".

You get a Faberge Egg quality motor.

Seriously: I just bought one and opened it up here. It's completely 
clean, inside and out. Not a dent or scratch. The bottom rubber seal is 
completely new, and the bearings are so smooth you can feel the natural 
resistance of the magnets. It's really impressive.

I'm tempted to take it apart, but I think I'll order another pair of 
them. Not because the outside motors need replacement, but because this 
thing is so good....

Just need to pull the hub from one of my older motors, but that's not 
too big of a deal....

C


On 6/15/2018 12:57 PM, HR HankRalston com wrote:
> I only need one to rotate  out the one that I think I can have repaired 
> here
> in Rochester NY.
> Prefer to have a matching tall one, but any should do for now.
> Hate to keep pushing the one going bad, but the grass is really growing
> fast.  Wish I discovered it last fall instead.
> PS  could use some new rubber on the front 2 wheels too!
>
> Thanks,
> Hank
> Office: (585) 697-0880
> Proud Member of Rochester Rotary since 2001
> Happy ~1970 ET15 owner, with snow thrower
>
> -----Original Message-----
> From: Pestka Dennis [mailto:dennispestka4 hotmail com]
> Sent: Thursday, June 14, 2018 12:24 PM
>
> Subject: Re: (ET) Looking for some deck motors
>
> Kansas Wind Power use to have some, but that's been a while. Also Harold
> Zimmerman, or the Tractor Store.
>
> Sent from my iPhone
>
> > On Jun 14, 2018, at 9:43 AM, "David Roden" <etpost drmm net> wrote:
> >
> > > On 14 Jun 2018 at 5:13, Cameron B wrote:
> > >
> > > ITMm looking for 2 mower deck motors.  I donTMt currently have the
> > > time nor shop set up properly to be able to rebuilt them.
> >
> > When the deck motors on my New Idea rider needed some work, I took
> > them to a local auto electric shop.  AFAICT, they did a fine job.  The
> > same place also replaced a noisy bearing in the drive motor.
> >
> >
> > David Roden - Akron, Ohio, USA
> >
> > = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
> > Note: mail sent to the "etpost" address will not reach me.  To send me
> > a private message, please use the address shown at the bottom of this
> > page : http://www.evdl.org/help/ = = = = = = = = = = = = = = = = = = =
> > = = = = = = = = = = = = = =
> >
> >
> >
> >
> > _______________________________________________
> > Elec-trak mailing list
> > Elec-trak cosmos phy tufts edu
> > https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
>
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
>
>
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak