[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ET) Capacitor removal...



They are most definitely there.Once you have experienced the aroma, you 
will
never forget it.I had a capacitor that had started leaking. I called the
poison control center in Pittsburgh, concerning how to properly dispose of
it. Believe it or not, the recommendation was, to wrap it in several 
plastic
bags, and dispose of it in the trash. The logic, if you can call it that,
was the amount of PCB was so small, it posed no danger. I hope that fifty
other people do not get the same idea, at the same time. Especially if they
all have the same refuse hauler.


RJ Kanary
Member TRNi  Since 1998
ASE® Certified Master Auto Technician

rjkanary nauticom net

----- Original Message -----
From: "Hazen, Dwight L" <hazen indiana edu>
To: <elec-trak cosmos phy tufts edu>
Sent: Friday, June 21, 2002 5:12 PM
Subject: RE: (ET) Capacitor removal...


> And I wonder about PCBs in the old capacitor.
>
>  Dwight
>
> Dwight L. Hazen, Indiana University, UITS
> Bloomington, In. 47408-7378 Phone 812-855-5367 hazen indiana edu
> http://php.ucs.indiana.edu/~hazen/ Ham Radio wb9tlh arrl net
> IP Phone 317.278.4014   Change is inevitable except from a vending
machine.
>
>
> -----Original Message-----
> From: David Roden (Akron OH USA) [mailto:roden ald net]
> Sent: Friday, June 21, 2002 4:03 PM
> To: elec-trak cosmos phy tufts edu
> Subject: Re: (ET) Capacitor removal...
>
> On 21 Jun 2002 at 16:47, Elie, Larry (L.D.) wrote:
>
> > First, I got a GE motor-RUN capacitor, 4 micro-Farads, 660V, (I think
the
> 330
> > and 440 are OK too) same rating, style, polarity (non) and vendor as 
> > the
> > original, $4 and change at Granger.  Very cheap.
>
> You say "electrolytic," but the cap apparently shouldn't really be one.  
> A
> friend of mine who's an electrical engineer and an EV old-timer advised 
> me
> strongly against using an electrolytic in a ferroresonant charger.  He 
> was
> referring to a Lester charger, but the GE's principle is the same.  Here
are
>
> his words:
>
> > They need to be high quality AC-rated dry film or oil-impregated
> > paper capacitors. NOT electrolytics or DC-rated film capacitors!
> > For efficiency, the capacitors need to have a low ESR and low
> > losses. The capacitor winding is normally wound to produce
> > high voltages, so 330vac to 660vac rated capacitors are
> > normally used.
> >
> > The capacitance value is critical if you want good regulation.
> > They usually use 2% to 4% accuracy, or hand-pick the capacitor
> > to trim the output voltage to the desired value.
> >
>
>
> David Roden - Akron, Ohio, USA
> 1991 Solectria Force 144vac
> 1991 Ford Escort Green/EV 128vdc
> 1970 GE Elec-trak E15 36vdc
> 1974 Avco New Idea 36vdc
> = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
> Thou shalt not send me any thing which says unto thee, "send this to all
>
>
> thou knowest."  Neither shalt thou send me any spam, lest I smite thee.
>
>
> = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
>
>
> Est. yearly US cost to safeguard Persian Gulf oil supply: $50 billion
>
>
> Est. 2001 value of US crude oil imports from Persian Gulf: $19 billion
> -- Harper's Index, April 2002
>
> = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
>
>