[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: (ET) Mower motor bearing replacement



Thanks Steve.  I was using a note for the MAIN motor, not the MOWER motor!

Larry


-----Original Message-----
From: SteveS [mailto:ssawtelle fcc net]
Sent: Wednesday, June 05, 2002 11:04 AM
To: elec-trak cosmos phy tufts edu
Subject: Re: (ET) Mower motor bearing replacement


Look in the files section of the site:

http://groups.yahoo.com/group/elec-trak/files/ET_PARTS.txt

When I was searching for similiar info, I put everything I found in this
file to help out the next person(s).

Now, I have the small diameter motor, so I can't vouch for the bearings
listed for the large dia motor, but I believe the info to be right as it 
was
listed a couple times in mesages and never contradicted.

SteveS
E12S

----- Original Message -----
From: "Elie, Larry (L.D.)" <lelie ford com>
To: "'Steven Naugler'" <snaugler earthlink net>; <>
Sent: Wednesday, June 05, 2002 10:09 AM
Subject: RE: (ET) Mower motor bearing replacement


> I thought I had kept the bearing numbers for the original bearings, as
well as some much improved, full sealed bearings.  I can't find them.  Does
anyone have the actual bearing numbers for the 4.5" dia motors handy?  I
need to re-cross reference them.
>
> Larry Elie
>
>
> -----Original Message-----
> From: Steven Naugler [mailto:snaugler earthlink net]
> Sent: Sunday, May 19, 2002 3:07 PM
> To: elec-trak cosmos phy tufts edu
> Subject: Re: (ET) Mower motor bearing replacement
>
>
> I have done this technique of using a bolt screwed into the end of the
motor
> shaft on 6 small diameter motors and 3 large diameter motors.  If a few
> cases the flange came off very easily, but most of the time I used a 
> press
> because I had one available.
>
> If you don't have a press you can use a wheel puller so long as you do 
> the
> following two things:
>
> 1.  Pull on the small diameter portion of the blade flange assembly.  If
you
> pull on the larger diameter flange itself you could bend it.  If bent it
is
> unlikely you could straighten it out enough that your mower blade will 
> run
> true.  You may need a split bearing puller to reach around the flange.
>
> 2.  Make sure that the screw of your puller stays on the bolt.  Being
> careful may be enough, but why don't you use a center punch and put a
dimple
> in the center of the head of the bolt.  This way the little nib on the 
> end
> of your puller screw will have something to keep it centered on the bolt.
>
> Steve Naugler
> snaugler earthlink net
>
> ----- Original Message -----
> From: <Oasis654 aol com>
> To: <tcoate coate org>; <owner-elec-trak cosmos phy tufts edu>;
> <elec-trak cosmos phy tufts edu>
> Sent: Sunday, May 19, 2002 12:32 PM
> Subject: Re: (ET) Mower motor bearing replacement
>
>
> >
> > In a message dated 5/18/02 11:24:28 PM, tcoate coate org wrote:
> >
> > << want to change the bearings on a large style mower motor.  In order
to
> do
> > that, you need to pull off the flange gadget at the end of the shaft
where
> > the blade attaches.  Is there some trick that I'm missing in order to
> doing
> > that?
> >
> > I put a bearing separator under the flange and pulled about as hard as 
> > I
> > dared with a good size puller.  the thing didn't budge at all.  Is 
> > there
> > any sort of key down in the slot on the shaft that needs to come out
> > first?  If so, how?  Or is it likely to be rust?  And if it is, is 
> > there
> > anything I can do about that?
> > >>
> >
> > hi folks, the problem may be that you're trying to pull and push on the
> blade
> > flange at the same time.  you have to put a strong bolt into the flange
> hole
> > where you'd normally bolt on the blade.  then by pushing on the bolt,
and
> > pulling on the blade flange, it should come off.  i've only seen this
done
> > with a press.
> >     good luck, jon k albany, ny
> >
>
>