Re: (ET) trouble...she no go

["e s" <stupidemail5 lycos com>]

model is 26ae12aa, sn kn27989

Still appears the 1 section diagrams are closer. 

looks like already there is a jumper on pins 10 to 11, apparently 
eliminating the time delay on the 1a relay


Keith



---------[ Received Mail Content ]----------

 Subject : Re: (ET) trouble...she no go

 Date : Sun, 10 Aug 2008 21:02:27 -0400 (EDT)

 From : "e s" <stupidemail5 lycos com>

 To : "RJ Kanary" <rjkanary nauticom net>

 Cc : elec-trak cosmos phy tufts edu


 p {margin-top:0px;margin-bottom:0px;}    So it would appear that the 
diagrams on pgs 1-33 to 1-36 are the correct ones for my machines?


It feels to me like the fwd rev relay is getting switched but has no 
current to its contacts

There is no current draw according to the gauge

Keith





---------[ Received Mail Content ]----------

 Subject : Re: (ET) trouble...she no go

 Date : Sun, 10 Aug 2008 12:09:35 -0400

 From : RJ Kanary <rjkanary nauticom net>

 To : e s <stupidemail5 lycos com>

 Cc : elec-trak cosmos phy tufts edu


There's a GOOD reason for that. E-12 S &amp; E-15 AA to GA don't HAVE an 
RTN 
relay. The RTN functions are contained in the silicon skulduggery on 
Card #1.

RJ


e s wrote:
> What is confusing me a bit is the RTN relay, which is on the schematic 
> for the E12 [3a-c on pg 3a-6] and does not seem to exist on my machine, 
> or in some other manuals
>
> Keith
>
>
>
> ---------[ Received Mail Content ]----------
>
> Subject : Re: (ET) trouble...she no go
>
> Date : Sun, 10 Aug 2008 10:49:34 -0400 (EDT)
>
> From : "e s" 
>
> To : 
>
>
> p {margin-top:0px;margin-bottom:0px;} It looks like the switch is in 
> series with the seat switch, so when open it stops all power, IOW the 
> f/r relay doesn't click. So I don't think that is it, unless I am 
> missing something
>
>
>
>
>
> ---------[ Received Mail Content ]----------
>
> Subject : Re: (ET) trouble...she no go
>
> Date : Sun, 10 Aug 2008 07:33:02 -0700 (PDT)
>
> From : jim donovan 
>
> To : e s , Electric Tractor 
>
>
> If it was working prior to doing brake work I would check the brake 
> safety micro-switch. Sounds like it is "on", meaning that the tractor 
> will not drive.
> 
> Just my thought.
> 
> Jim
>
> --- On Sun, 8/10/08, e s wrote:
>
> From: e s 
> Subject: (ET) trouble...she no go
> To: Elec-trak cosmos phy tufts edu
> Date: Sunday, August 10, 2008, 8:48 AM
>
> So i replaced the fwd/rev relay and it ran just fine, plenty of battery, 
> no
> worries, just no brakes.
>
> fixed the brakes [note, stupid placement of caliper, 1/2 inch different 
> and it
> would be a 2 minute job] 
>
> Now she no go. Fwd rev relay clicks back and forth, but no power drain. 
> PTO
> lights lift all work
>
> Have manuals but haven't deciphered the troubleshooting diagrams. Part of
> the problem is lack of labeling on the machine 
>
> jumped out the brake and seat switch to test. no dice
>
> hints welcome................
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
>
>
>
> 
> 
> ------------------------------------------------------------------------
>
> _______________________________________________
> Elec-trak mailing list
> Elec-trak cosmos phy tufts edu
> https://cosmos.phy.tufts.edu/mailman/listinfo/elec-trak
>